Even though you may be enjoying the end of summer, it is a good idea to start thinking about getting your furnace ready for winter use.

If you keep good maintenance records of your HVAC equipment and did not have any issues the previous winter, it is probably safe to turn on your furnace once or twice when a cool night comes along.

However, you should get your system inspected by a professional contractor to prevent any unexpected break-downs.

What does furnace maintenance cover?

A good furnace check-up has many benefits. During an inspection, your technician will check your gas ignition system, tighten all the electrical connections, and verify the gas pressure and test the ignition system. More importantly, he will inspect the heat exchanger for any damage or cracks.

In a gas furnace, the heat exchanger is an airtight vessel which transfer’s combustion gases which exit the home through the flue. A damaged or cracked heat exchanger is very dangerous.  The system should be shut down immediately until it can be repaired or replaced. 

Professional technicians can identify and address small problems before they progress into inconvenient, serious issues.

Beaver Brothers, Inc. has been Salisbury’s trusted source since 1919!

The Importance of maintenance for Salisbury, NC homeowners

We often find that no-heat calls in the winter are related to the lack of HVAC maintenance. By not scheduling your fall maintenance, it could lead to a health hazard in your home. Your maintenance visit can reveal carbon monoxide leaks, which are difficult to detect because the gas is odorless and colorless. Carbon monoxide poisoning can cause headaches, dizziness, nausea and even death.

If your furnace is found to be unsafe, your technician will shut your furnace off to ensure your family’s safety.

Simple things Salisbury area residents can do this fall can make a big impact!

There are a few things homeowners can do to get the furnace ready for winter. Look for drafty areas around your home, such as cracks in doors and windows and make necessary repairs. Replace the batteries and test your carbon monoxide detector. Make sure it is working properly and test the device.

Make sure to keep the area surrounding your furnace unobstructed, especially items considered a fire danger. Replace the air filter. A dirty filter restricts airflow, decreases the efficiency of your system and forces components to work harder. Also, walk around your home and clean the air vents, removing any dust or pet hair.

Of course, an in-depth maintenance should be scheduled with a local HVAC contractor to ensure your heating system is operating at optimum performance for the upcoming winter season.

Contact Salisbury’s local experts at Beaver Brothers, Inc. to have your heating system checked today!

Maximize Your Home Comfort

How to Maximize the Comfort & Efficiency of My HVAC System in Salisbury, NC?

Home ownership requires a lot of responsibility.

Monitoring, overseeing, and maintaining many of the mechanical elements of your home are crucial to keeping the home in good condition.

HVAC, which means “heating, ventilation, and air-conditioning,” is the equipment responsible for maintaining a comfortable temperature in your home.

It is also what preserves optimal air quality and energy efficiency.

Here are a few tips on how to maximize the comfort and efficiency of your HVAC system, regardless of the equipment’s age.

Salisbury Homeowners, Please Change Your Filters Regularly

Air filters are easy for homeowners to monitor and change.

The type of filtration you have determines how often the filters should be replaced.

Some filters must be changed monthly. Some higher-end air filtration systems can go six-months before they need to be replaced.

Every homeowner should know the location and what type of filters they have protecting their HVAC system.

Maintenance is a Must for Salisbury Homeowners!

A professional service contractor like Beaver Brothers, Inc. should inspect your HVAC system twice a year, once in the cooling season and again in the heating season.

This is important to ensure your system is operating at its optimal level for the appropriate season’s temperatures.

In the fall or winter, technicians should inspect and service your furnace or heater. In the spring or summer, they return to concentrate on your air-conditioner.

Most professional companies offer incentives for homeowners to sign up as a maintenance agreement customer.

Benefits can include priority service and discounts on repairs.

Close curtains or blinds during the day

During the summer months, closing the curtains can reduce some of the ambient heat load on your home.

The opposite happens during the winter; and by keeping your blinds open, you can take advantage of the sun’s warming rays.

The blinds keep the warm air inside the home, as opposed to “leaking” out through the windows.

Make sure your vents and returns are not obstructed

If you have a forced air heating and cooling system, your air vents are strategically place throughout your home.

These can be located on the wall, ceiling, or in the floor.

It is important NOT to cover up these air vents.

Blocking the vents restricts the air flow and will cause your furnace or air-conditioner to work harder to keep your home comfortable.

This decreases the efficiency of your system, and it will cost you more to operate. 

Clear obstructions around your outdoor unit

It is important to keep the area surrounding the outdoor section of your HVAC system clear of any obstructions.

Shrubbery and plants allow air to pass through their foliage; however, make sure they are not in too close a proximity to your outdoor unit.

One foot of clearance around your outdoor condenser should be sufficient, but the more clearance you have the better.

Because air is drawn into the air-conditioner, you will want to make sure any walls are at least 16-18 inches away from the unit.

Warm air is discharged upwards from the unit, therefore, clearance above the unit is important.

Blockage of air can result in damage to the system’s compressor and other components.

If you have a heat pump system; it is not only important to keep the area around the unit clear in the summer; but as well as the winter.  You must keep the accumulation of snow or ice away from the outdoor heat pump.  It can cause the outdoor unit to stop working.

If you are expecting snow, make sure to remove the snow on and around the heat pump.

Make sure your system is turned off before working near it; this can be accomplished by turn the system off at the thermostat.  An extra measure of safety would be to pull the disconnect located at the outdoor unit.

If you follow these basic tips, you will increase the efficiency of your HVAC equipment and maintain a comfortable temperature no matter what time of year.

Beavers Brothers, Inc. have been a fixture in the Salisbury community since 1918! 

 Contact us now and become part of the Beaver family!

The Impact of the Phase Out of R-22 on Your Aging HVAC System in Lake Norman

R22 refrigerant is a commonly used refrigerant in domestic air conditioners. It is a compound that includes chlorine and fluorine, which can potentially deplete the ozone layer.  This can lead to enhancing the greenhouse effect, which has studies showing negative effects on our environment.

In 1987, an international treaty called the Montreal Protocol was universally ratified and was designed to phase out substances that contributed to ozone depletion. The United States was a party to this treaty, so the EPA decided to implement a plan to phase out R22. The date was set for January 2020, where all R22 was banned (meaning it was illegal to import or manufacture R22). 

Prior to this date, there were exceptions for R22.  The EPA began scaling back and limiting the production. It could be used to service existing air conditioners that had leaks in their refrigerant system.  Now; that it is no longer in production, the cost of R22 continues to rise. Some refrigerant manufacturers have introduced products to act as a replacement for R22, such as M099 (R438a).  Please be very careful with these products, because they can lead to refrigerant contamination. Not all equipment manufacturers approve this product as a direct replacement, so your best bet is to consult your local servicing HVAC contractor for the facts.  Beaver Brothers is here to help and answer any questions!

Increased Cost to Repair R22 Systems in Davidson or Mooresville

Homeowners and business owners alike that have older air conditioners, may be faced with a difficult decision when a repair is required for your system. Depending upon the repair, it may make sense to repair your system versus replacing it.  Your local heating and air company; Beaver Brothers, Inc., can provide you with the best solution. While it may be tempting to keep your unit as long as possible; you most certainly will pay more for repairs going forward. This is due to the increased cost of R22 and the availability of R22 refrigerant.

Be Proactive or Wait in Salisbury?

Now that it is illegal to manufacture or import new R22, you really need to weigh the options for your aging air conditioner.  Have a discussion with your servicing HVAC company and consider your options. They are the experts and can help you make the best decision.  It is better to be proactive now. If you wait to the dead of summer; you may be faced with large repair bills and an uncomfortable home or office. Here are the things to discuss and consider with your service provider:

  • Age of your system
  • Recent Repairs
  • Energy Costs
  • Potential utility or manufacturer rebates on a new system
  • Energy Savings
  • Better Warranty

Being proactive about repairs or replacement for your home’s most valuable appliance is never a bad thing.  While your business or home still has air conditioning, you can take your time choosing a new system that fits your needs and budget. Research your cooling needs and speak to your professional at Beaver Brothers about which unit will be right for you. 

If you wait to replace it, then you may find yourself in the middle of summer without air conditioning. You should consider these factors if you choose to wait for your current air conditioner fails:

  • Contractors are very busy in the summer, you may have to wait
  • Availability of the equipment
  • Installation time (which means days without air conditioning)
  • You may have to make a quicker decision than you would like

Either way, get your research done and talk to your local professional at Beaver Brothers, Inc. about your next steps.

Should I Have a Fall Furnace Safety Inspection in Salisbury or Kannapolis?

It is important to make sure that your heating unit is prepared for the upcoming winter ahead, and how crucial it is to have a Fall Safety Inspection. You may think your heating system is clean and working fine, but do you really know that is it safe? Beaver Brothers’ fall safety check will provide you and your family peace of mind knowing your heating unit is ready for the cold winter months ahead.  The Farmers’ Almanac is predicting a cold winter this year.  Read below to find out more about the importance of Sheer’s fall safety check.

Prevention is the Best Medicine in Rowan County

Fall Tune-Ups and Inspections are a great way to ensure that your heating unit is clean and functioning at the correct factory specifications. Having an inspection is about preventative care, it gives your trained HVAC technician an opportunity to spot a problem and fix it before you have a system breakdown.

Preventative care is one of the best ways to safeguard your heating system against unnecessary wear and tear, as well as maximize the longevity of it.

Cracked Heat Exchangers are Dangerous

When your trained technician from Beaver Brothers Heating and Air Conditioning performs a Fall Safety Inspection, they will inspect your heat exchanger. The heat exchanger is a set of coils inside the furnace that are responsible for heating the air in your home. These coils are contained within the furnace. The burner sends combustion gases into the heat exchanger while the blower motor sends the air from the blower across the heat exchanger. Then the heat exchanger warms the air and sends it back into your home. This process creates exhaust gases that are released outside through the flue.

The heat exchanger is vital to heating your home all winter. Unfortunately, heat exchangers can crack over time which can pose a threat to your family’s safety. When a heat exchanger cracks it can cause carbon monoxide to leak into your home. 

Normal use of your furnace causes wear and tear. The heat exchanger expands and contracts in order to heat your home. Years of expansion and contraction may lead to cracking or small leaks. If it is cracked, your trained service tech can advise you as to whether you should replace the part or possibly replace the entire system. 

While heat exchangers will crack due to old age, they should last you at least fifteen years. Proper care and regular maintenance will maximize the life of your heat exchanger. 

Carbon Monoxide

Carbon monoxide; also known as the silent killer, is an odorless, colorless, and tasteless gas that can be potentially life-threatening.

There are several ways carbon monoxide can show up in your home. Carbon monoxide is created whenever fuels (such as gasoline, wood, coal, natural gas, propane, oil, and methane) are burned incompletely. Anything used in the home that burns these fuels has the potential to cause carbon monoxide to leak into your home.

Everyday heating appliances can be the source of a carbon monoxide leak and should be properly ventilated. Boilers, water heaters, and fireplaces all burn fossil fuels and are potentially dangerous.

Furnaces can be a potential source of carbon monoxide when the heat exchanger cracks. A cracked heat exchanger releases carbon monoxide into the air circulated throughout your home. Having a certified technician from Beaver Brothers perform a Fall Safety Inspection can prevent this from happening in your home. Schedule your safety inspection now with Beaver Brothers Heating & Air Conditioning. Your certified technician will independently test for carbon monoxide throughout your home and show you the results.  North Carolina code also requires homeowners to have a carbon monoxide detector in their home, if they have a fossil fuel burning appliance.
Contact us now to schedule your safety check or if we can answer any questions for you.  One of our qualified customer service representatives will be glad to help!

How to Cut Your Utility Bill in Half This Summer Concord & Salisbury, NC

Summer is the favorite time of year for many of us. Those warm summer nights and long days which include vacations, swimming, kids playing outdoors, and picnics at the park. But along with the fun of summer comes the dreaded high utility bills. Summer is hot, especially here in Carolinas. It’s too hot to keep your windows open, so your air conditioner runs all day and night just to keep you comfortable. With utility rate increases, your power bill probably keeps getting higher and higher. What can you do to cut costs and potentially cut your bill in half this summer? 

Replace Air Filters in Salisbury

Clean air filters help your air conditioner operate efficiently. Dirty and clogged air filters are a major contributor to higher utility bills because your air conditioner has to work harder to circulate the air throughout your home. It will also help with allergies and asthma. Check them once a month and replace them when necessary.

Avoid Operating Appliances that Generate Heat in Concord, NC

Your oven, dryer, and dishwasher create a lot of heat that heats up your house every time you use them. Try to find alternatives whenever possible, and you will see savings over time. 

Instead of using the oven, you can cook on the stovetop, use a crockpot, or even fire up the grill. 

Don’t use the dryer, hang your clothes outside to dry. If you suffer from summer allergies; look for places around your home where you can layout the laundry to dry or look into purchasing drying racks.

Water heaters require energy to maintain hot water in the tank. Wash your laundry and dishes in cold water to save energy. 

Instead of using the dishwasher, wash dishes by hand and let them air dry. 

If you need to use the dryer or dishwasher, run them in the early mornings or overnight. Also, make sure you’ve cleaned your dryer traps and vents.

Keep Your Blinds and Curtains Closed from Direct Light

If you’re away from home, keep all your blinds and curtains closed. It’s best to keep the blinds or curtains closed during hot sunny hours.  It will significantly lower the temperature in your home. When you are home and want to use natural light to save energy, only open the blinds or curtains that will let in indirect light.  

Use Fans

Ceiling fans are a great cost-effective way to cool you off. Just remember to turn your ceiling fan to run counterclockwise during the summer.

If you don’t have ceiling fans, look into investing in portable fans. You can find inexpensive fans that have several different speeds, settings, and even come with remotes. 

Use your bathroom fan when you take a shower. A bathroom fan will remove heat and humidity from the bathroom and home. 

Try Using Low Flow Shower Heads

Install low flow showerheads that reduce the amount of water consumption when you shower.

Turn Down Your Water Heater or Go Tankless

Most thermostats are set at 140 degrees. Turning it down to 120 degrees will lower your utility bills and still maintain a comfortable water temperature. Your water heater uses energy to maintain a constant water temperature. By lowering the temperature your water heater uses less energy. 

Because tankless water heaters only work when you turn on hot water, they use less energy than standard water heaters. Switching to a tankless water heater may lower your utility bills. 

Use LED Light Bulbs 

Once your incandescent light bulbs stop working, replace them with LED bulbs. LED bulbs are more expensive but last much longer and use 80 to 90% less energy than incandescent light bulbs, providing you savings.

Turn It Off and Use Power Strips

Turn off lights, computers, and televisions. Unplug phones and tablets when not charging. Simple steps like these can make a big difference in the amount of electricity you and your home consume. You can even plug your electronics and appliances into power strips. Turn the power strip off when you can. Many of our electronics and appliances use energy even when they’re not in use.

Raise Your Thermostat in Concord

Keep your thermostat at a comfortable temperature but not too cool. Try turning it up a couple of degrees and see if your home is still comfortable. Keep it as high as possible while still maintaining your comfort level. A few degrees higher on the thermostat will save you money.

Invest in a Programmable or Smart Thermostat

You can lower your cooling bill as much as 10% by turning your temperatures down seven to ten degrees. A programmable thermostat allows you to set a schedule which would increase the temperatures during the times you’re not there. 

You could also purchase a smart thermostat which allows you to control the temperature in your home remotely through a smartphone, tablet, remote control, or by voice. More advanced smart thermostats actually “learn” from your behaviors. Over time, they recognize and remember your regular heating and cooling habits. They will determine the most appropriate temperature based on the time of year, the time of day, the number of occupants, and previous patterns of use. 

Properly Insulate Your Home

Before summer is in full swing, make sure your home is properly insulated. Once you turn your air conditioner on, you want to keep the cool air in and the hot air out. Check windows and doors for places where air may be getting in or out. If needed, caulk windows and replace weather stripping on the doors. 

Check the ductwork in your attic or crawlspaces for leaks. A properly insulated home will help keep down costs and preserve energy. 

Regular Service or Maintenance from Beaver Brothers, Inc.

Keeping to a regular maintenance schedule will ensure that your unit is working efficiently, thus, reducing the amount of energy used.

Signs Your Air Conditioner is Oversized or Undersized in Concord, NC

Did you know that air conditioning systems are designed to work properly within certain sized homes?  The size of your home should influence what size unit you should purchase. Many homeowners are unaware that the size of their home is a key consideration when purchasing a new air conditioner. Some people think the bigger the better.  They may think that a bigger air conditioner will function better and cool their home faster. This simply is not true. Many homeowners look to save costs and may purchase a smaller unit. They believe that air conditioner manufacturers offer bigger models and more expensive models just to make more money. This isn’t true either.

How does a homeowner know whether their unit is sized right for their home, and what are the signs that the unit they have may be oversized or undersized?

It’s Too Small to cool your home in Concord or Kannapolis

It’s not uncommon for an air conditioning unit to be too small for the size of the home. You may suspect the unit is too small when the unit in running and blowing cold air, but your house doesn’t reach the desired temperature on your thermostat.  It is working too hard to keep up with your cooling needs. A unit that is too small will have unnecessary wear and tear and potentially freeze the evaporator coils. You may also notice higher utility bills. Keep this in mind though when the system is being sized for your home.  There is a fine line between the correct size air conditioning system for your home and outdoor design temperature. The outdoor design temperature in North Carolina is between 91– 93 degrees.  So, when the temperature is above these conditions; even a properly sized A/C unit may not cool your home to your desired temperature.

The A/C unit may be TOO BIG…..The unit constantly stops and starts?

Bigger isn’t better! When you have an oversized heating and air system, the air conditioner will cycle on and off again in short bursts. This can lead to unnecessary wear and tear on your system, as well as cause your system to run inefficiently. When it cycles on and off; it isn’t running long enough to let the air flow through the system and filter properly. It also can’t properly dehumidify the air. By properly dehumidifying the air; it reduces the moisture content in the air, which will make it feel more comfortable at a higher temperature. Another sign your unit is too big is higher utility bills.  This is caused by the constant starting and stopping. It actually saves you money to have the system run longer! An inefficient system will always cost you more on your bills.

It’s Just Right for your Concord home

An air conditioner that is sized properly is an air conditioner that is efficient. It will run through enough cycles to keep your home at your desired temperature and reduce humidity without running in bursts, shutting on and off again, or working too hard.

Speak to the Experts at Beaver Brothers, Inc.

The best way to know if your air conditioner is the right size for your home is to speak with a professional. Your highly trained HVAC technician at Beaver Brothers will determine the right load capacity for your home. They will measure your home, look at window placement and direction, whether your home is properly insulated, and do a room by room calculation. At that point, your HVAC technician will discuss what the best options are for your home comfort.

What Causes a Cracked Heat Exchanger on My Furnace? Should I be Worried About my Family’s Safety?

The heat exchanger is an important and potentially dangerous component to your heating system. The heat exchanger is a set of coils or tubes inside the furnace that is responsible for heating the air in your home. These coils are contained within an airtight combustion chamber. The burner ignites the gas that enters the heat exchanger.  As the heat exchanger warms, the blower or fan motor forces air across it. The warm air is then circulated throughout your home for heat. This process produces exhaust gases, which are expelled outside the home through your furnace flue.

The heat exchanger is vital to heating your home all winter. Unfortunately, heat exchangers can crack and leak, which poses a potential threat to your family’s safety. When a heat exchanger cracks it can cause carbon monoxide to enter into your home. Carbon monoxide, also known as the “silent killer”, is an odorless, colorless, and tasteless gas that can be potentially life threatening.

What can you do to keep your family safe? First, always have carbon monoxide detectors throughout your home. Make sure you have at least one on every floor of your home. Now, let’s look at understanding what causes a cracked heat exchanger and how you can prevent it.

Poor Air Flow in Huntersville, NC

The number one culprit for poor airflow is a clogged air filter. When filters are clogged with dust and debris, it impedes return airflow back to the furnace.  If the return airflow is significantly reduced, the heat exchanger can become overheated and crack. Make sure to change your air filters regularly.

Undersized Return Air Flow in Mooresville, NC

When the return ductwork in your home is undersized, then your furnace does not receive the proper return airflow. Air needs to be evenly distributed throughout your home for your heating system to work efficiently. When there is too little return airflow, the heat exchanger may overheat and crack. Have your certified HVAC technician from Beaver Brothers, Inc. check your return to ensure it is sized properly for your heating system.

Oversized Furnaces That Short Cycle in Cornelius, NC

Another reason for a cracked heat exchanger may be that your furnace is too large for your home. When you have an oversized furnace, it will frequently cycle on and off again, causing your heat exchanger to expand and contract too frequently.  It is satisfying the thermostat temperature too quickly and not giving the furnace adequate run time. Eventually, this can lead to a cracked heat exchanger. The experts at Beaver Brothers are highly trained to determine the appropriate size furnace for your home. If we determine your home has an oversized furnace, it may be in the best interest of safety to replace the furnace.

Age of system

Normal use of your furnace causes wear and tear. The heat exchanger expands and contracts during the normal heating process. Years of expansion and contraction may lead to cracking. The experts at Beaver Brothers can help you determine the best solution for your home.

No Maintenance Can Shorten its Life

While heat exchangers will crack due to old age, a properly maintained furnace should last you approximately fifteen years. Proper care and regular maintenance from the team at Beaver Brothers, Inc. will maximize the life of your heat exchanger and furnace. If you have further questions, please contact us.

Ways to Stay Warm and Save Energy This Winter in Concord & Kannapolis

After a hot Carolina summer and fall, cool air is certainly a welcomed change. You may have pulled out the sweaters and coats, but is your home ready for the winter? Read below to learn about some simple ways to stay warm and save energy at the same time.

Open Blinds and Curtains During the Day in Concord, NC

Too often, people keep the blinds and curtains closed during winter months to try and keep the heat in their house. If your home is properly insulated, open the blinds and curtains so that they may allow the sun to enter and heat the room. Not only is sunlight good to combat the winter gloom, it won’t cost you anything to warm your home naturally.

Throw on Another Blanket and Lower Your Thermostat

While you may be tempted to turn up the thermostat when you feel cold, try a blanket instead. Keep some throw blankets on the couch and add another layer onto your bedding. You can stay warm and save money. Did you know you can save up to 10% per year on your heating bills by reducing your home’s temperature by one degree?

Reverse Your Ceiling Fan

A great way to beat the heat is to turn on ceiling fans, but did you know that ceiling fans can help keep you warm in the winter months too? Reverse the ceiling fan cycle so that it turns clockwise if you are looking up at the fan.  By doing this, the fan pulls the warm air up and circulates it around the room. Keep it at a low speed and make sure that it rotates clockwise.

Insulate Your Home in Kannapolis, NC

The best thing you can do to keep down heating costs during the winter months is to make sure your home is properly insulated. First, check your windows and doors for potential leaks. If needed, caulk around the windows and replace weather stripping.

Make sure the ducts in the attics and crawlspaces are properly insulated. Run your hand along the heating ducts for holes. If you feel warm air escaping, then you’ll need to have your ductwork sealed and insulated by a professional contractor.  

Change Your Filters

Replacing your filters is an inexpensive and a highly effective way to keep heating costs down. It’s also essential to caring for your furnace. Always remember, no matter what season, a clogged filter makes your heating and air units work harder and less efficient. Change your filters every three months at minimum.

Service Your Furnace in Concord & Kannapolis

A regular maintenance schedule is necessary to maintain a safe and efficient furnace. Your certified HVAC technician at Beaver Brothers, Inc. will inspect your furnace to ensure it is functioning to best of its ability.  If you need to schedule heating maintenance or have further questions, please contact us!

Why is My Air Conditioner Constantly Running  and My House Still Isn’t Cool on Lake Norman?

Lake Norman summers are hot and humid and air conditioners work overtime. If you’re wondering whether it’s normal for your air conditioner to constantly run, consider the temperatures outside and whether your house is cooling. When temperatures reach in the upper eighties and nineties, your air conditioner will have to work harder to keep the temperatures lower in your home. Your air conditioner should turn on and stay on until your house cools. But, what about if your house isn’t cooling and your air conditioner just keeps running? Read below to find out what might be wrong with your unit.

It’s Too Small for Your Lake Norman Home

It’s not uncommon for an air unit to be too small for the size of the home. You may suspect the unit is undersized when the unit is blowing cold air, but your house doesn’t reach the desired temperature of your thermostat. If this is the case, contact Beaver Brothers now and ask them to perform a load calculation and determine the cooling needs of your home. An undersized unit may cause unnecessary wear and tear on system and could lead to your system freezing up.

Clogged Air Filters in Rowan County

It’s an easy fix and an inexpensive way to prevent your air unit from unnecessary wear and tear. Change your filters monthly and make sure you keep them clean.

Evaporator Coil Problems

If your unit is running constantly and warm air is coming out of the vents, then it’s possible the evaporator coils are dirty or frozen. A semi-annual maintenance check up with Beaver Brothers will keep the evaporator coils clean and enable them to work properly. If you suspect the coils are frozen, turn off your air conditioner and call us immediately. If the indoor evaporator coil is indeed frozen, you should turn the fan to the “on” position on your thermostat. This will allow the indoor coil to unthaw and enable us to check the system properly upon arrival. A Beaver Brothers technician will check for low refrigerant levels as this could be another reason your air conditioner isn’t cooling your home.

Problems with the Outdoor Unit

Just like your indoor evaporator coils the outdoor condenser coil may be dirty or clogged. Check your outdoor unit and make sure that it is clear from debris and grime. Scheduling semi-annual maintenance is a great way to keep your outdoor unit in clean, working condition. If your outdoor unit appears to be clean and running properly, it’s best to contact us to and we can provide you with a professional consultation.

Contact the Experts at Beaver Brothers online or by phone at (704)766-8889

DIY Summer Energy Savings Tips for Salisbury and Lake Norman Residents

Summer has arrived and temperatures are quickly rising. Hot summers mean high energy bills. Follow these homeowner tips to help save energy and money this summer.

Schedule summer maintenance for your HVAC system from Beaver Brothers, Inc.

Call or schedule online to have one of our professional technicians at Beaver Brothers to perform your summer maintenance and ensure that your air conditioner is working properly all summer long.

Turn your thermostat up a degree or two

Keep your thermostat at a comfortable temperature but not too cool. Try turning it up a couple degrees and see if your home is still comfortable. 74 degrees over 72 feels great when it’s 95 outside! The harder your air conditioner works, the shorter its lifespan and the more you’ll pay on your next monthly utility bill.

Replace filters monthly

Clean filters help your air conditioner operate more efficiently and cut down on the amount of dust and pollen in your home.

Avoid heat-generating activities

During summer months, it’s best to avoid using the oven. Instead, use the stovetop, microwave, or grill. If you need to use the dryer or dishwasher, run them in the early mornings or overnight. Consider hand washing dishes and air drying your clothes during the hottest days.

Keep your blinds and curtains closed from direct light on Lake Norman

If you’re away from the house, keep all your blinds and curtains closed. When you’re at home and want to use natural light to save energy, only open the blinds or curtains if that part of your home is not under direct light. Also, make sure you are using energy efficient lightbulbs.

Use a ceiling fan in Salisbury

Ceiling fans are a cost-effective way to cool you off. They help circulate cool air and feels cool on contact to your skin. Because a ceiling fan doesn’t lower the temperature of the room, it’s best to turn it off when you leave a room.

Remember, an inefficient air conditioner means more money out of your pocket. Don’t forget to call Beaver Brothers, Inc. to schedule your summer maintenance today!

Call us today! (704)766-8889